Site Specific Safety and Health Program

Consigli Construction Co., Inc. Project #2855

Table of Contents

Roles and Responsibilities 2

Site Orientation 4

Policy Enforcement 4

Planning 5

Site Safety Inspections 5

Site Parking/ Access/ Logistics 7

Project team Contact Hierarchy 9

Emergency Management 11

Medical Facilities 14

Scope of Proposed Operations 16

Pfizer Specific Requirements 17

Consigli Safety Requirements 19

Incident/Injury/Near Miss reporting and first aid 23

Post incident review 23

Evacuation 23

Jobsite Gym 27

Environmental 28

Adjacent property 30

Exposure to street traffic 30

Emergency Response Plan

ALL EMERGENCIES SHOULD BE REPORTED BY CALLING Security- 617-674-7001

EMERGENCY TYPE

The following situations are considered emergency response actions and should be handled in accordance with the procedures outlined in this plan.

Fire/Explosion
Serious Injury/Fatalities
Structural Damage/Collapse
Weather or Geological Event
Environmental Incident
Utility Damage
Illegal Activity
Labor Problems
Bomb Threats/Military Ordinance Unearthing/Acts of Terrorism

Life safety systems in the building will remain active. Smoke detectors in the working areas will be removed to avoid accidental alarms, and all sprinkler heads will be turned upward once ceiling grid has been removed. All CFD/ Pfizer impairment requirements will be followed for shutdowns, and sprinkler permits will be pulled prior to impacting any fire suppression systems.

In the event of an emergency the following policy will be adhered to for the safe evacuation of the Project.

An evacuation will be ordered for life threatening emergencies (collapse, explosion, fire). Person/persons discovering emergency shall take the following actions:

A Consigli representative will be dispatched to the front entrance to the project at the entrance of the building to meet the responding Emergency Personnel and advise the individual in charge of the location of any chemicals or hazardous substances that may be present on any of the floors. SDS’s will be readily available if needed by the Cambridge Fire Dept.

In the event of a serious injury requiring the assistance of Pfizer Emergency Response Teams or Cambridge EMS the injured worker will be kept as comfortable as possible. Emergency first aid, if necessary, may be administered. Under no circumstances will the injured person be moved unless the worker’s life is in danger because of fire or calamity.

In the event an evacuation is required all personnel at this job site will assemble outside of the work area at the designated Muster Point at the grass park directly adjacent to the loading dock. The foreman for each company will meet at that location and take a count of their staff. If for some reason a worker is unaccounted for, the fire department will be notified of the last location where the worker was observed.

Incident reporting protocol– an incident report will be generated by Consigli super within 24 hours of the incident occurring, or once the scene has been stabilized. This will be completed and tracked using Quickbase, and will automatically distribute to CCC personnel upon completion. Once distributed, the original author will share with the following Pfizer personnel- Keisy Marquez, Alexandra Puglielli, Bob Clark, Patrick Lynch, Demetra Barlas, Greg Rexford

In line with Pfizer commitments and the philosophy of “Goal Zero,” S.A.F.E.: Staying Accident Free Every Day is the Safety Mission that forms the very foundation of the Consigli Safety Culture. The S.A.F.E. mission, which is supported by technology, (Predictive Solutions internal auditing instrument which identifies and defines leading indicator related information); Leadership (Empowering our team members to assure safe projects); Humanization (Protect the ones you love by protecting yourself); Jobsite Gym for Riggs Employees (Morning warm-up stretch program); Training (Integrating sub-contractors into the Consigli Safety Culture); and Lean (nothing hit the ground), is the driving force behind Consigli’ s drive to our vision – ZERO. ZERO is the philosophy that all accidents are preventable and that no accident is acceptable. The S.A.F.E. mission is the guiding force to achieving the Consigli Safety Vision which is ZERO.

Roles and Responsibilities: It is understood that Consigli Construction will serve as the controlling entity for the 4^th and 5^th floor spaces that it is contracted to work in. This requires that the occupied space is made safe each and every day through extensive planning between Consigli, Pfizer, and all subcontractors on site. Consigli has very defined set of roles and responsibilities for each project team member in order to maintain a safe site from mobilization to demobilization. All project team members have the obligation, and authority to stop any unsafe acts taking place in the site.

For more information regarding roles and responsibilities please see Chapter 1 of the Consigli Corporate Safety Program.

Superintendent TIM BACKLIN: The superintendent is responsible for the jobsite 24/7. The superintendent supervises all work in the field and is responsible for ensuring that all tasks being performed have been adequately planned. This will include the implementation of the following SOPs:

Approval of safe permits to work.
Collection and submission of all subcontractor JHAs to Pfizer 14 days prior to work mobilization for all subcontractors.
Collection of all subcontractor JSAs, tool box talks, equipment inspections, SDS, Safety and health programs.
Ensuring 100% compliance with all badging and security requirements
Ensure 100% compliance with all orientation requirements, as well as all training requirements for Pfizer
Create daily safety observations for the jobsite, and track in Procore.
Attend safety audits conducted by the Consigli Safety Department
Maintain first aid/ CPR certification, and OSHA 30
Report any and all incidents to Pfizer contacts as well as Consigli Safety/ general superintendent.
Directly communicate with Keisy Marques and Alexandra Puglielli
Implementing and enforcing all requirements stipulated in this plan.

Project Manager, Brandon Oxner: The project manager is responsible for working with subcontractors prior to mobilization in order to attain all necessary documentation to be submitted prior to work beginning. Pretask planning takes place from the time we buy the subcontractor out and carries through to their daily JSAs. Brandon will be responsible for the following.

Schedule and manage the subcontractor safety preconstruction meeting between the subcontractor’s foreman, safety manager, and Consigli safety department.
Manage the Consigli safety violation program with subcontractors as needed.
Serve as a liaison with subcontractor project management staff, and Pfizer project management as needed.

Assistant Project Manager, James Flynn: The APM’s major focus is to serve as document control. James will manage the following:

Meeting minutes for all safety meetings, and team meetings.
Collection of all documents requested at the time of the subcontractor safety preconstruction meeting.
Early collection of all JHA’s and SDS to be submitted to Pfizer as close to subcontractor buyout as possible.

Regional Safety Manager, Dan Della-Giustina Jr: The Consigli safety department will be required to maintain the site specific safety program, and update it throughout the duration of the job. Dan’s role will not only serve to audit the project but to provide a resource to the project team in the following ways:

Safety preconstruction inspection- Predictive Solutions- conducted at the time of the preop
Construction safety inspections- Predictive Solutions
Monthly Management Audits- Predictive Solutions

General Superintendent/ Project Executive, Dean Archambault and Erick Lacy: The GS, and PX serve as resources to the Consigli project team. They will attend safety meetings as needed, communicate with Pfizer personnel, and serve to hold the team accountable to the high standard of safety that Consigli Requires.

Site Orientation: All individuals working on this project including Pfizer personnel will receive a comprehensive Safety Orientation delivered by the Consigli Superintendent (TIM BACKLIN) which will cover Pfizer safety rules and procedures as well as communicating Consigli specific and Pfizer KSQ2 safety requirements. Site badging and Pfizer Online Contractor Orientation Course shall be completed by all workers, who will be working on site for greater than one week, and all subcontractor foremen, prior-to or as a part of the initial site orientation.

The Consigli Orientation is conducted daily, by the superintendent, and is required by all workers entering the project. It consists of two part: a general set of Consigli rules and policies to be followed (shown in the form of a video: link Below), and a site specific portion which is reviewed in person by the Consigli superintendent.

Once both parts are completed, the worker will scan a QR code which directs them to a Quickbase link where they will upload their name, contractor, hardhat sticker number, and any certifications required of them per Consigli, according to their trade.

A hardhat sticker will be given to each worker once orientation is complete, and the number on the sticker will correspond with the worker’s location in the Quickbase Orientation log

PLEAS REVIEW THE SITE SPEIFIC ORIENTATION ACCOMPANIING THIS PLAN.

All personnel working on site shall have a minimum of OSHA 10 Hour Construction Safety Outreach Training. Foremen are required to have an OSHA 30 Hour Construction Safety Outreach Training. Proof of training will be required during site orientation.

https://vimeo.com/consigli/review/528995743/c6233ac631

Policy Enforcement: All project personnel will be required to adhere to the OSHA 1926 Standard for Construction throughout their occupation on site. Because this is a minimum set of guidelines, the Consgili Safety and Health Program has added additional measures to ensure that workers are not exposed to hazards on the jobsite. Consigli goes above and beyond in the following Categories:

Fall protection- 6 foot fall rule for all workers on site
Hot work safety
Electrical Safety
Daily JSAs and Weekly Tool Box Talks

Please refer to the Consigli Safety and Health program for more Information

Because of the nature of the facility, Pfizer also has a Contractor Safety Handbook which will outline additional measures that will be required of all workers including but not limited to the following:

Cut level 4 gloves required for all workers
JHAs and Safe Work Permits for all tasks
Hot work Safety
Scissor Lift Safety
Ladders Last Policy
Lockout Tag out
Noise cannot exceed 82 decibels over an 8 hour TWA

Please refer to the Pfizer Contractor Safety Manual for more information

Planning: The project team, as well as Consigli Safety Department, will meet with each subcontractor before they start to review their Site-Specific Safety and Health Program and all project specific Job Safety Analyses. The project team shall be an integrated mix of Pfizer, architect, engineer and Consigli Construction personnel. After reviewing the programs and meeting with the individual subcontractor, if the team is satisfied with the risk control direction, they will be permitted to begin work.

All required PPE will be worn at all times by all workers in the working space. This will be outlined in the specific JHA for each task.

See below PPE section within this plan

Site communication will be continuously provided with the use of Safety Boards posted onsite. These boards will contain necessary information for those entering the site to work as well as visitors to the site. Emergency information and contacts will be available on the jobsite Safety Boards as well.

Site Safety Inspections: A site Safety Inspection will be completed by a Safety Professional of the Consigli Safety Department on the site (minimum) weekly. Pfizer EH&S and Project Management will be notified prior to these inspections to allow them to be available to join the walkthrough. These inspections will be copied to the Pfizer EH&S staff (Alexandra Puglielli) Cambridge_EHS@pfizer.com in the form of an emailed report. In addition to the weekly safety walks, each job site will receive a management compliance review on a monthly basis. During the management review, safety managers will evaluate administrative safety paperwork for compliance.

SEE APPENDIX I OF THE CONSIGI SAFETY AND HEALTH PROGRAM FOR THESE INSPECTIONS

These inspections will be conducted using the Predictive Solutions auditing software. Inspections are conducted using hand-held devices (iPad or iPhone) and are synced up to a data base, as well as shared with the distribution added online. All reports will be distributed via email within one hour of the inspection completing. Monthly reports shall be generated by the Consigli safety department and shared with all individuals on the distribution to encompass any leading indicator trends. The following recipients will receive these reports: Superintendent TIM BACKLIN, Brandon Oxner, James Flynn, Dean Archambault, Pfizer EH&S, Erick Lacy,

During the job site safety walks, Safety managers will note all observations during the walk. Any unsafe conditions or actions will be assigned a severity level. Inspection software tool, Predictive Solutions, will calculate a score based on the observations weighing the severity of any unsafe observations. Each unsafe observation will generate a corrective action, to be assigned a contractor responsible, severity, an antecedent, a party responsible for corrective action, an action taken, a completed time and date if completed, and location of observation with a detailed description.

The superintendent is responsible for conducting daily safety observations. These observations will be documented within the Daily Log on Procore. Observations made onsite will be discussed and reviewed at the daily stand-up meeting. Alexandra Puglielli and Keisy Marquez will be added to the distribution of all daily logs, allowing them access to safety observations as well.

The auditing of these observations are tracked in the “Monthly Management Audit” conducted on predictive solutions

Site Access / Parking: A detailed logistics plan has been created for the project that details delivery routes, employee access, and parking. Employee parking will not be impacted during this work. Worker access shall be from the loading dock located at the back driveway of the KSQ2 building. Restrooms will be designated in the working areas on the 4^th and 5^th floors per direction of CCC and Pfizer. Access for workers entering the project will be at the loading dock at which point, each worker will either present their badge to security or sign in with the attendant. Elevator 4 will be designated for worker access to the 4^th and 5^th floors, and will be used for all deliveries/ load out of trash and debris. Consigli will require all load out of trash and debris to be “live loaded”. No dumpster will be left on site for longer than it takes to load.

Public Safety: All workers will maintain 0 fraternization with any Pfizer employees while they are accessing occupied areas. Occasionally our work will require us to be in the common areas of the facility, and workers will need access to occupied locations for general access

Cafeteria, Loading dock, Elevators will require worker access It is to this end that workers need to be cognizant of their surroundings.

Tripping hazards are to be taken care of immediately and materials are not permitted to be stored in public ways.

The right-of-way will always be granted to the public.

Containment of our work areas is crucial to the protection of the public from flying objects, dust, debris, falling objects, etc. All work areas will be 100% contained with either a hard STARC barrier or poly barrier

Further logistics to be coordinated once Consigli mobilizes and throughout construction.

Consigli Project Team/Staffing

The following is a list of the Chain of Command/Call Hierarchy on the project for establishing lines of communication for all emergencies. ALL CONSIGLI EMPLOYEES LISTED BELOW WILL ATTAIN BADGED ACCESS INTO THE FACILITY
CALL HIERARCHY

Back– End of Emergency Response Plan

Emergency Contact Names and Numbers

First call: Pfizer Emergency Response 617-674-7001
2^nd Call: Consigli Project Superintendent: TIM BACKLIN (508)922-6019
*** TIM BACKLIN will initiategroup text to Pfizer and Consigli Team (Ally Puglielli, Demetra Barlas, Keisy Marquez, Bob Clark, etc.) stating that:

“An incident occurred___ (details) _____”***

3^rd Call: Pfizer Safety Contact: Alexandra Puglielli (617)388-5951

4^th Call: Consigli Project Safety Manager: Dan Della-Giustina Jr (774)462-1481

5^th Call: Consigli Project Executive: Erick Lacy (508)922-7352

6^th Call: Consigli Safety Director: Bryan Kingsbury (508)808-9359

ADDITIONAL BADGED PROJECT CONTACT NUMBERS

Consigli General Superintendent: Dean Archambault (508) 958- 0138
Consigli Project Manager: Brandon Oxner (508)902-7664
Consigli APM: James Flynn (774)573-1891
Consigli PE Payton Bielawski (774)462 2040
Consigli PE Robbie Paro (774)573 1585
Pfizer Project Manager – Keisy Marquez (857) 294-4414
Pfizer Project Manager- Greg Roxford (978)580-4310
Bob Clark- Project Manager- (978)625- 1933
Cambridge Police – Non-Emergency (617) 349-3300
Cambridge Fire Department – Non-Emergency (617) 349-4900
Cambridge Public Works – Non-Emergency (617) 349-4800
OCC Med CIC (617) 367-5002
Massachusetts General Hospital – ER (617)724-4100

Ragon Institute Contact Information

Chad Nixon- Superintendent: (617)438-7803

Cory Pinheiro- Project Executive:(774)217-8866

Scope and Contacts for Sub-Contractors on KSQ2 4 and 5 Renovation

Duct and Piping Insulation
Finnbar Mechanical- See Procore
Sheet Metal and VAV Install
Tremont HVAC- See Procore
Testing & Balancing:
Cox Engineering
Fire Protection Piping and Sprinkler Install
JC Cannistraro
Plumbing and Mechanical Piping
JC Cannistraro: Glenn Gibbons (617)592-0805
Doors, Frames and Hardware (Furnish Only)
O’Conner Door:Bill Quackenbush (978)500-5532
Millwork Fabrication (Furnish Only)
Blessington: Melissa Marien mmarien@blessington.net
Flooring and Ceramic Tile
Power, Lighting, Fire Alarm, Controls and Sound Masking
McDonald Electric: Dave Keenan dkeenan@mcdonaldcorp.com
Painting and Wall Covering
Clean-Up and Housekeeping
Riggs Contracting: James Flynn (774)573 1891
Demountable Partitions, Vertical Blinds
Infinium Matthew Zeszotek (216)990-7425
Framing, Drywall, ACT and Doors, Frames and Hardware, Millwork
Tightline Construction

Back– End of Emergency Contact Names and Numbers

Medical Facilities

OccMed CIC

10 Hawthrone Pl Suite 114 Boston MA 02114

(617)367- 5002

Emergency Department/Hospital

Massachusetts General Hospital- ER

55 Fruit St Boston MA 02114

(617)724- 4100

Back– End of Medical Facilities

Site Safety Plan

Scope of Proposed Operations: Beginning in June 2022 and finishing February 2023, this project will entail the renovation of an area within the existing KSQ2 Building located at the Pfizer campus in Cambridge, MA.

Project Description: Pfizer will endeavor to renovate approximately 19,000 SF of interior office and laboratory space in KSQ 2 Level 4 with approximately 10-15% impact to existing architecture and utilities.

Current scope includes phased construction of the 4^th floor with additional work above ceiling on the 3^rd floor and mechanical/ electrical/ plumbing, systems on the 1^st floor. The project will consist of the construction management services for the renovation of the existing office and lab space including commissioning support to turn over the newly renovated space.

Some additional scopes of work have been added to the total load of work Consigli is taking on. These scopes of work are as follows:

Project 8311- Construction for approximately three weeks. Expansion of KSQ2 lab space including demolition of drywall and rebuild. Some additional ductwork to be added as well.

Project 8312- Demolition of glass partition walls during a single weekend, and patching of carpet flooring.

The work will commence with selective demolition. Demolition work needed in this scope will include duct work, metal studs/drywall, and selective mechanical/ electrical/ plumbing / fire protection demolition.

Mechanical/Electrical/Plumbing/Fire Protection (mechanical/ electrical/ plumbing / fire protection) work will include upgrades and rerouting of some existing equipment as well as the installation of new mechanical/ electrical/ plumbing / fire protection systems for the Pfizer end user. Work areas will be separated from other existing occupied spaces with secure barriers and necessary access to shared building locations (corridors, exit routes, etc.) will be coordinated with Pfizer Facilities and Project Management.

The project will include the repair of any damaged fireproofing. The sealing of all floor and wall penetrations will be completed as well. The project will finish with installation of new office and lab partitions and finishes (paint, ceiling, floor, etc.) before turn-over to Pfizer occupancy and equipment/furniture installation. The Pfizer operational readiness review and safety pre-start-up review shall be completed prior to this turn-over.

The following site-specific safety plan will detail safety approach to aspects of this project regarding safety and be supplemented with requirements from Consigli Safety Program, Pfizer Environmental Health and Safety Requirements, and Pfizer Security Requirements.

Safety Related Aspects of the Job include:

Site Security: Managed through site badging requirements and site safety orientation.
Life Safety Impacts: All egress routes and building life safety systems will be maintained or impaired (sprinkler) only after extensive facilities review/approval.
Mechanical Coordination: Review of existing systems and coordination with facility access managers. Lock out/ Tag out (LO/TO) procedures followed with Pfizer.
Working at Height: Use of personnel lifts and scaffold by trained users with fully installed fall protection.
Tool Use: pre-use inspection of tools. JSA review of safe too use and review of alternative safer too options.
Material Handing: Safety lifting techniques and clear access reviewed in JSA process. Use of material handing assistive tools/carts.
Hot Work: All How Work will be permitted through the Pfizer Hot Work Permit Process by Authorized Permit Issuer involved in the work. Fire watch required.
Electrical work: No live policy in effect. Use of GFCI circuits on all electrical tools.
Concrete Saw Cutting: Hot Work Program followed. Silica and noise controls detailed in the JSA and confirmed during activity.
Installation of finish products: Review of SDS and safe handling/disposal.

Slip/Trip/Fall Hazards: Managed through continuous housekeeping and materials management.

Pfizer Specific Requirements

(For more information please refer to Pfizer Contractor Safety Manual)

Handling asphyxiants: It is not anticipated that any handling of asphyxiant gasses will take place throughout the scope of this project. If this specific task does take place

Prequalification: The only subcontractors that will be awarded packages for work on the KSQ2 project will be ISNET approved contractors. All contractors approved to work on the KSQ2 project will required to maintain a grade from A-C. Any contractor with a grade form B-C will be required to adhere to additional safety requirements per Pfizer Requirements. All subcontractors will be responsible for maintaining their approved status throughout the duration of the project.

Safe Work Permit : All construction activities will be required to take place under a Safe Work Permit. Safe Work Permits will be completed on a weekly basis with each individual subcontractor designated as the “Permit Requestor”. A “Permit Issuer” (CCC Representative) will sign off on each individual permit only after it has been thoroughly reviewed; work will begin only after it has been determined that the work will move forward in a safe manner by CCC. All CCC representatives who are designated as a “Permit Issuer” will undergo the required training provided by Pfizer. If at any point an unforeseen condition shall arise, work must stop immediately until the permit can be adjusted for the new task being performed.

If applicable, additional Hazardous Work Permits may be required. The Safety Permit to Work Issuer will make that determination

Job Hazard Analysis JHA: All contractors are responsible for submitting JHAs prior to beginning any construction activity on site. Each subcontractor must include all tasks pertaining to their specific scope of work in the JHA, or submit multiple to contain the necessary amount of detail. JHAs must be submitted to Pfizer EHS FOURTEEN BUSINESS DAYS prior to mobilization. Work can commence on site only once Pfizer EHS has reviewed, the JHA. Please see below attachment:

Badging and Training: All construction workers who will work on site for greater than one week must undergo the proper screening procedure to be given a badge to enter the site. Workers who are not badged must be signed in and out each day at their assigned point of entry into the building. All badged workers shall undergo contractor safety training conducted Pfizer EHS. Consigli will maintain a strict 0 tolerance policy regarding security and badging requirements for all CCC and Subcontractor personnel.

Lock Out/ Tag Out-

THIS SECTION TO BE UPDATED ONCE ONBOARDING OF ALL RELEVEANT SUBCONTRACTORS IS COMPLETE

All lock out/ Tag out operations designed to control the flow of hazardous energies will be conducted in adherence with the Consigli Safety Program as well as all Pfizer EHS requirements. JLL will be responsible for managing and reviewing all LO/TO procedures. Adequate locks, and tags shall be maintained at all times by the competent person of the contractor who is conducting the work.

Tags will be required to contain the following information:

Name of the person who applied the lock
Date lock was applied
Phone number of person who applied lock
Reason for LO/TO

Any inadequate controls will result in a complete stoppage of work until the proper corrections have been made. A Facility Interruption Prevention Plan shall be implemented for each LO/TO operation to be conducted, and shall be submitted to JLL prior to mobilization of said task.

This will include, but may not be limited to:

Existing, and temporary power systems
Fire protection Systems
Existing water valves/ plumbing

Ladders Last : Ladders shall not be used on site, unless all other elevated working platforms have been ruled out due to safety, or general feasibility. All work from ladders must be detailed in the subcontractors JHA, approved by Pfizer EHS, and be reviewed with the worker performing that task. All work from ladders will also be outlined in the subcontractor’s Safe Work Permit. Proof of training will be submitted to Pfizer EHS prior to any worker accessing a ladder. All work from ladders shall take place only after authorization of Consigli Construction has been attained. ALL WORKERS UTILIZING LADDERS MUST COMPLETE THE LADDER SAFETY TRAINING ATTACHED WITH THIS PROGRAM.

This “ladders last” approach will be clearly identified for all trades onsite during pre-construction and orientation. The use of mobile scaffolds and mobile work platforms are expected for this project.

If ladders/podium ladders are used for work at height, it will be done correctly per manufacturer’s recommendations and only after a pre-use inspection is completed. Any worker who is on a ladder/podium ladder and could be exposed to a fall greater than the height of their work on the podium will be required to tie off. Ladders will not be used as a form of access to a walking /working level. Only podium ladders with a rating Type 1A or 1AA will be allowed on Consigli projects. Wooden ladders are not to be permitted.

Consigli Safety Requirements

Pretask Plans: Pre-task Plans, Job Safety analysis or other similar type shall be conducted prior to all and any operation. JSA’s shall be conducted on a daily basis by all subcontractors on site, and be submitted to CCC once reviewed. Said plan is to be reviewed initially with all involved personnel performing that task, signed by all workers including their supervisor and filed on site.-

Please see appendix M of the Consigli Safety Program

PERSONAL PROTECTIVE EQUIPMENT

All personal protective equipment shall meet all federal specifications and standards. All PPE will be provided new (hardhats, gloves, respirators, safety glasses) with emphasis on clean storage and maintenance stressed. Employee owned PPE is required to meet all applicable regulations and standards. Subcontractors shall supply their workers with all required PPE.

Project Superintendents shall be responsible for assuring that all Consigli employees and subcontractors comply with the Personal Protective Equipment Program. The Safety Department will periodically audit for field compliance. Requirements involve:

Workers to be thoroughly indoctrinated and trained in the instinctive use of required protective equipment. Defective or unacceptable PPE will be removed immediately from service.
This job shall be a Mandatory Hard Hat Job- Hard hats must show their company logo and must display the workers hard hat sticker from the Pfizer ksq2 project.
This project requires 100% eye protection. ANSI Z87 Minimum Rating. The use of face shields for overhead work must be evaluated.
All workers will be required to don ANSI cut resistant level 4 gloves-Minimum- at all times per Pfizer EHS
Arm protection gauntlets (ANSI Cut Resistance Level 6) shall be worn when potential for arm lacerations exist.
JSA’s need to document hand and finger hazards, and glove selection and use for protecting against said hazard.
Employees shall be provided with face protection equipment when power tools, machines or operations present potential eye or face injury from physical, chemical, or radiation agents.
Hearing protection against the effects of noise exposure shall be worn when sound levels exceed 82 dba- Per Pfizer on site. Hearing protection shall be available at all times in the Consigli project trailer/office upon employee request.
Respirators/nuisance masks will not be allowed to be used on a voluntary basis in accordance with Pfizer requirements.
Safety harnesses with lanyards, preventing a free drop of more than six feet, shall be worn by all workers on elevated locations not protected with railings. The same equipment shall also be worn on unprotected platforms. Safety lines shall be sufficiently anchored.
Impermeable rubber or any impenetrable protection shall be worn to prevent skin contact with any acid, chemical, creosote, coal tar, fuel oil or concrete. This is especially true for Consigli masons utilizing acid washes.
No machines, tools, etc. will be operated until all manufacturer required guards and auxiliary handles are in place, and the worker has been trained in the safe use of said tool.
All PPE shall be inspected by the individual user prior to each use. Damaged/ inadequate PPE shall be taken out of service immediately and replaced by the employer.
At no time shall any worker be allowed to work on site alone. Known as the “lone worker rule”, at least 2 workers must be on site at all times in order for one to be able to respond to an incident, accident, or emergency arising from the other’s task. The CCC superintendent will qualify as a second worker so long as he is in the working space.

Demolition: Selective demolition scope is anticipated. Removal of metal studs, duct work, and some Mechanical, Electrical, Plumbing/ Fire Protection demolition will be required for the new layouts.

Prior to the start of demo operations, the contractor preforming demo will confirm that all utilities leading into the area have been made safe. The electrician will disconnect and lock out all electrical, the plumber will do the same with any plumbing lines, and the HVAC subcontractor will do the same on the HVAC piping and duct work. Lock out/tag out will be reviewed during the pre-construction safety meetings to assure disconnect and protection of existing utilities is safe for any construction activities to commence. In spaces where some electrical or mechanical must remain live, a color-coding system will be utilized for easy identification of live utilities that must stay active and utilities that must be removed. Any and all utilities spray painted/ labeled Red are not to be touched and need to be protected during all operations. Utilities spray painted/ labeled Green are to be removed as part of the selective demolition process only after lock-out/tag-out has been confirmed and utilities tested. If any utilities are unmarked, they shall be considered live. All equipment labeled “OS”, as well as all lighting on the Cambridge campus is “backfed” from generators. Cat III voltage testers required for zero energy verification. The demo contractor will be responsible for completing CCC Demo Checklist- Appendix BBB of Consigli Corporate Safety and Health Program, prior to the start of any work in their target areas.

The following procedures are to be followed when performing demolition:

Planning of the demolition activities taking place on site will begin at the safety preconstruction meeting held between the Consigli project team/ safety department and the demolition subcontractor.
Prior to any demolition being performed, a hazardous materials survey must be

performed to include any building materials that may contain asbestos, lead,

PCBs, mercury, refrigerant, etc.

If the demolition is to involve structural components of the building, then a plan

must be prepared by a competent person, then reviewed by a structural engineer.

An engineered stamp may be required.

A survey must be completed of all utilities in the building in order to assess

whether or not these systems are live or have been disabled/made safe. Green

and red spray paint/ tape/ markings are to be used to identify which systems are live (red) and which are dead, and therefore safe to demo (green).

All pertinent LO/TO procedures will be followed, and documentation of make safe will per required prior to demolition.
A pre-demo checklist (APPENDIX BBB) must be completed before beginning

demolition in a new area.

Debris from demolition must be removed throughout the work day, paying special

attention to combustible materials. Walking/working surfaces are to be kept free

and clear of debris at all times.

Dust control must be maintained at all times through the use of air filtration,

misting with water, use of sweeping compound, etc.

When cutting overhead or using a grinder, a face shield must be worn

Fall Protection: The existing space does not present significant fall protection risk (i.e. leading edge, roof work, floor/wall openings.) All work over 6 feet will require a Safe Permit-to-Work and some form of fall protection in accordance with Consigli fall protection policy. All PFAS anchor points shall be determined to be adequate by the competent person. The adequacy of each anchor will be determined by the task at hand, and will be updated in that crew’s JHA/ safe permit to work.

Anticipated work from heights may include, but are not limited to:

Ceiling Demolition/ construction

Mechanical, electrical, plumbing/ fire protection work,

Drywall and metal frame demolition/ construction

Holes greater than 2” will be covered and made fire safe with acceptable material will be secured and marked “HOLE” (cover must be able to withstand four times the intended load). Hole covers will stay in place until the hole/penetration has been filled. Core holes will have curbs built around them in order to prevent spills from migrating through the hole into the space below.

Scaffold and elevated work platforms: It is expected that small, mobile types of scaffold will be used throughout the project. These types of scaffolding will take favor over ladders in order to gain height. If ladders prove to be the only tool available to perform a specific task, then their use must be detailed in the subcontractor’s safe permit to work, and JHA. When used, scaffolds will be inspected daily before each shift by a competent person designated by each contractor using it. The inspections will be documented on the Consigli inspection checklist. After inspecting, scaffold “tags” located at the access point to each scaffold will be initialed by representative subcontractor competent person. A scaffold checklist will be provided by CCC to the subcontractors’ designated persons to aid them with their inspection. This checklist will be filled out prior to the beginning of each shift and filed in the construction office. Overhead protection will be provided for any access points into the building.

** Please review chapter 14 of the Consigli Corporate Safety and Health Program for additional details.

Scissor Lifts/MEWP: It is expected there will be scissor lifts/Mobile Elevating Work Platforms utilized in the fit-out work, mainly scissor lifts on the slab. Area and slab conditions in the intended work area will be inspected for overhead hazard, depressions, covers, or any other unsafe condition which causes the potential for an incident. Scissor lift/MEWP will be inspected before each use, [PA1] by a competent person designated by each individual contractor, and documented on the CCC Scissor lift inspection Checklist Appendix HH. Per Pfizer Requirements, no worker in a lift [PA2] will be permitted to raise its basket, or lower its basket without the assistance of a spotter to assure that no obstructions are in the way of being struck by the machine. MEWPs cannot be moved while in an elevated position. If the MEWP needs to relocate, the basket needs to be lowered first. Operators must exit the platform when moving through areas with limited height or width. All work from lifts will be a minimum, of a two man operation due to this policy. All contractors who will be performing work from a lift will provide documented proof of training to Consigli for all workers who will be using said lift. Workers will be tied off to the anchor point within basket at all times when using an aerial/ scissor lift.

Chemical and Materials: All Materials and chemicals used on-site will have been previously submitted for review by Pfizer EH&S and approved for use within the Cambridge site. A Safety Data Sheet (SDS)must be provided before product is brought onsite.

SDS sheets on file in Consigli Construction’s Site Safety Plan
All SDS sheets shall be readily accessible.
At the close of the project the material certification regarding “no asbestos” will be updated and issued to Pfizer.

** Please review chapter 20 of the Consigli Corporate Safety and Health Program for additional details.

Fire Protection: A detailed fire protection plan will be in place on the project and updated as required. All hot work to be conducted on this project will be done with the Pfizer Hot Work Permit program fully implemented. This will be coordinated through the Consigli Hot Work Permit Authorizer

as well as Pfizer and the Cambridge Fire Department (if required). All personnel involved in the hot work activity shall be trained in NFPA course on Hot Work Safety as required by the Commonwealth of MA.

Flammables will not be stored inside the building, or on the property. Fire Extinguishers will be installed on stands or hooks, and conspicuously located throughout the project. They will be part of the daily inspection with extinguisher log completed monthly. There is no smoking allowed anywhere on the property.

**Review Chapter 17 of the Consigli Corporate Safety and Health Program for more detail.

Control of Hazardous Energies- All mechanical, electrical, plumbing, etc. systems that require work to be performed on them shall be effectively LOTO to a de-energized state. These procedures shall follow in strict accordance with the OSHA requirements in 1910.147 – Control of Hazardous Energy, NFPA 70E, NFPA 99, etc. In most cases, the facility will have procedures already established for this work. In every case, shutdowns of all types are required to be coordinated with the Facilities Management team. At no time will work be performed on any system prior to this meeting taking place.

Electrical: All electricians working on site shall be adequately trained in specific safety requirements pertinent to working with electrical components. These trainings shall be documented, in order for CCC to confirm their completion. These trainings should include, all, but not limited to the following:

NFPA 70E
OSHA Subpart K
ANSI
PPE Requirements
OSHA 10

All electrical tools, cords and equipment must be in good working order. To that end, all electrical tools and components must be visually checked on a daily basis. Any tools with damaged cords or damaged cords must be taken out service immediately. All cords must be equipped with a ground pin, flat three wire cords are not allowed. SJO and SJT or other similarly rated cords only shall be used. Cords must be 12 gauge or better. The electrician will be responsible for all temp power and any temp lighting that may be needed.

All temporary power for the project will be installed on protected and dedicated circuits with 100% GFCI protection. GFCI will be tested by the electric contractor weekly to assure proper function with a log book filed with CCC monthly. No live electrical work will be conducted per Pfizer and Consigli requirements. All shut-downs and confirmation of zero energy will be competed through the Pfizer Energized Electrical Work Permit process [PA3] , and be in compliane with NFPA 70E. All LO/TO will follow Pfizer requirements. Low voltages- Less than 50V must be guarded, and protected at all times. Work on low voltages must be encompassed in a JHA, and a safe permit to work.

**Review Chapter 26 of the Consigli Corporate Safety and Health Program for more detail

Incident/Injury/Near Miss reporting and First Aid Plan: Along with Pfizer reporting requirements, Consigli Construction shall follow Consigli Safety Program for incident reporting and first aid. At a minimum, all incidents shall be communicated to the project team and owner representative immediately with written report following within 24 hours. This report shall be completed on the Consigli Superintendents Incident report. Report any incidents to the Consigli Safety Director and Ally Puglielli (Pfizer.)

** Please review chapter 9 and 27 of the Consigli Corporate Safety and Health Program for additional details.

Post Incident Review: Any incident that results in a recordable injury will require a post incident review. The worker who was injured along with their foreman/Safety Personnel/PM/Sup/etc… will need to fill out Appendix N (post incident review form) and attend this meeting. At this meeting they will re-emphasize their commitment to safety, determine chronology of events, identify contributing factors, identify root cause, provide improvement plan to prevent reoccurrence and discuss disciplinary actions taken (if any). Findings from this meeting will be shared/disseminated with all contractors on site to prevent reoccurrence. Injury data will be track and shared with Pfizer.

Evacuation Plan (RACE, and Routes of Egress): Please refer to the Pfizer Cambridge Site Evacuation Assembly & Shelter Areas posted on the project information board and reviewed at orientation. All contractors’ employees shall attend the Consigli Construction Project Orientation. Consigli Construction’s Project Superintendent shall conduct safety orientation training with each employee and project subcontractors. Training will involve site specific safety and evacuation protocol.

Emergency Management Response: In the event of an Emergency the construction workers shall leave the building immediately. Point of assembly/muster shall be on the site evacuation plan. In the Event of a DISASTER, the Superintendent shall instruct the construction workers to leave the site or remain in place and await further instruction. Follow-up notification to Pfizer EH&S will be completed by the Consigli Superintendent. The following steps should be taken in the event of an emergency.

When reporting an emergency, please provide the following:

• Your location: Pfizer – KSQ2 Facility- Level 4/5, phone number, and name:
• Site Address: 610 Main St [PA4] . Cambridge, MA

• Nature and extent of the incident (injury, accident, spill, smoke/fire, damage, etc.);

• The name and amount of the material spilled (if applicable); and

• The safest route to the spill (if applicable).

** Please review chapter 8 of the Consigli Corporate Safety and Health Program for additional details.

Restricted Areas: Contractors are prohibited from entering any areas outside of the project unless work has been previously authorized and scheduled. All workers must limit their impact on surrounding areas to the largest extent feasible. No food or drink will be permitted in the work area. Breaks will be taken in designated break areas reviewed during site orientation. All deliveries shall be made at the loading dock coordinated with Consigli and Pfizer. Do not stage deliveries or trucks on the active parking lot, garage, or access roads outside of the building. No idling is permitted outside of the building.

Lean requirements/Materials Management/Housekeeping: Getting materials into and out of the project will be adequately planned. All deliveries are to be scheduled with the CCC Superintendent and coordinated with the KSQ2 staff. A comprehensive Job Safety Analysis shall be done on all materials that will be hoisted and placed into the building. Only materials which will be used/installed within three days’ time will be delivered to the site. Attention must be paid to structural analysis in regards to loading existing floors with material and equipment. Listed below are additional Lean requirements:

No materials shall be delivered to the site earlier than 3 days before said materials are to be installed/put into place. If materials have to be delivered before that 3 day time period, subcontractor shall get prior approval from Consigli Superintendent. Because of this, notification / scheduling is required for all deliveries to the site. Subcontractors must notify Contractor at least 24 hours in advance. Contractor has the right to refuse any deliveries not properly scheduled or due to logistical constraints as necessary.

All subcontractors’ delivered materials shall be placed on wheeled carts, wheeled racks or in wheeled bins so as to necessitate easy relocation in the event materials need to be moved. Carts, racks, or dollies shall not exceed manufacturers intended weight loads. Materials/tools can be delivered and stored on pallets only if pallet jacks are delivered simultaneously with said delivery to provide for ready mobility. Additionally, pallet jacks need to remain in immediate area. Each subcontractor will need to supply their own pallet jacks for their own materials and keep their pallet jack within reasonable distance at all times.

All workstations shall be provided with wheeled trash bins for immediate placement of all debris produced as a part of the subcontractors operations. All trash will be immediately placed in wheeled containers provided by Consigli.

All subcontractors shall use rubber wheeled carts when moving material or removing trash from a building. Any damage caused by the Subcontractor shall be repaired at the cost of the Subcontractor. Back charges will be appropriately assessed for the cost of the repairs. No trash or materials shall be left on the floor.

Subcontractors shall, where feasible, elevate all electrical extension cords, hoses, or cables – removing them from all walking/working surfaces. Electrical Cords, when elevated shall be supported or suspended in a manner that does not subject them to damage.

Storage of delivered materials in cardboard containers shall be discouraged. When materials must stay in cardboard containers, said containers shall be removed from the projects immediately after product is unpacked.

Subcontractor will participate in schedule development meetings as required by Consigli.

Jobsite Gym: Jobsite Gym is a 10-15 minute stretching/ warm up program, designed with the intent to reduce the number of soft tissue injuries throughout the typical day of a construction worker. Riggs Employees will be required to perform jobsite gym upon the start of their working shift. Jobsite Gym will take place within the construction area, and may be adjusted throughout the duration of the project to account for progress.

Back– End of Site Safety Plan

Environmental Emergency Contact and Management Response

IAQ (Indoor Air Quality): This project will occur in an occupied building. A baseline survey of the air quality in KSQ2 work area and accessible adjacent areas will be completed prior to the start of construction operations. Dust control, housekeeping, and frequent monitoring will ensure no impact on the air quality for the existing building occupants.

Starc Wall Panels, as well as poly sheathing will be used to create a negative pressure environment. Negative air machines fitted with HEPA filters will be used to ensure 0 dust mitigation outside of the designated working area. Periodic sampling of the public areas adjacent to the working space will be conducted in order to ensure 0 dust mitigation from the space.

** Please review chapter 29 of the Consigli Corporate Safety and Health Program for additional details

Asbestos: No ACM disturbance or removal is expected. A survey of the work areas (or similar) shall be conducted prior to the start of construction operations. A MA DEP AQ06 filing will be completed prior to the start of construction/alteration work. The findings of the building hazardous materials survey/inventory will be reviewed prior to the commencement of demolition and site activities.

This does not mean that asbestos could not still be found in other areas, caution must be used when working and if any workers identify any potentially hazardous substances then they should stop and notify their supervisor immediately. All identified asbestos will be fully abated by a licensed and regulated asbestos abatement contractor under a formal plan to be written, submitted and in accordance with the DEP.

IT IS THE RESPONSIBILITY OF ALL SUBCONTRACTOR FOREMEN TO REVIEW THE HAZARDOUS MATERIAL REPORT & CORRESPONDING ABATEMENT REPORT WITH THEIR WORKERS. A copy of the hazardous Material/abatement report will be on site at all times and available to anyone request it. All work and disposal will be done in compliance with state and federal regulations and standards

Lead: A survey of the work areas (or similar) shall be conducted prior to the start of construction operations. No lead is expected to be used or encountered during the construction of the KSQ2 office/ lab space.

** Please review chapter 29 of the Consigli Corporate Safety and Health Program for additional details

Silica: Any activity which can produce silica dust will use engineering controls to keep dust to a minimum. A written exposure plan must be developed for all silica producing tasks that clearly defines the following:

1) A description of the tasks in the workplace that involve exposure to respirable crystalline silica.

2) A description of the engineering controls, work practices, and respiratory protection used to limit employee exposure to respirable crystalline silica for each task.

3) A description of the housekeeping measures used to limit employee exposure to respirable crystalline silica.

4) A description of the procedures used to restrict access to work areas, when necessary, to minimize the number of employees exposed to respirable crystalline silica and their level of exposure, including exposures generated by other employers.

There will be no dry cutting of any masonry material allowed; if water cannot be used then a dustless vacuum system consisting of HEPA dust extraction system will be used. Prior to the project going full scale an exposure assessment of a worker grinding and cutting a silica containing material while using the HEPA system an exposure assessment will be done so as to establish the silica exposure level.

Polychlorinated Biphenyl’s (PCBs): Light ballast unless labeled “No PCB’S” will be designated PCB containing, All PCB containing material shall be removed and disposed of in accordance with all local, state, and federal regulations and be coordinated with Pfizer. All other inquiries or locations in regards to PCB containing material can be located in the Hazardous Material survey. If identified on any of the materials to be impacted, PCB‘s will be abated. Any and all PCB remediation will be performed by a licensed /qualified contractor

Mold: Mold issues are not anticipated to be prevalent on this project, however if mold is discovered, Consigli’s mold remediation policy will be implemented and followed.

** Please review chapter 22 of the Consigli Corporate Safety and Health Program for additional details

Consigli Environmental Emergencies/Response:

Consigli’s identified Emergency Response Subcontractor;

Name: Cyn Environmental Services, Inc. (781)341-1777

100 Tosca Drive Stoughton, MA 02072.

Noise: Pfizer restricts noise exposure to workers to 82 Decibels over an 8 hour TWA. Normal working hours will be between 7:00 am and 3:30 pm Mon-Fri. Noisy work will be restricted to before 9 am and after 5 pm. Noisy work will be defined by Pfizer on a case by case basis. Any contractor who may need to work late must first seek approval from the Superintendent. Noise levels will be monitored when high levels of noise could be expected to assure that noise levels do not exceed acceptable OSHA levels. Consigli permissible noise policy and procedures will be followed.

** Please review chapter 29 of the Consigli Corporate Safety and Health Program for additional details

Adjacent Property: Directly adjacent to the entrance into 1 Portland St is a Consigli Construction Site which will operate throughout the duration of this project. Chad Nixon and Cory Pinheiro are contacts for the adjacent job site:

Chad Nixon- (617)438-7803

Cory Pinheiro- (774)217-8866

All efforts will be made to ensure that property and roadways adjacent to the work, area remains un-impacted. It is anticipated that all work will be in the designated work areas within the building. Any deviation from that will require consultation with the Superintendent. The site logistics plan will but updated as necessary with regards to delivery routes, access and egress paths, and dumpster location.

Exposure to Street Traffic: It is anticipated that all deliveries will be made by way of the existing trucking route and loading dock. All speed limits will be obeyed, and deliveries will be made as to coincide with working hours. If temporary access routes are necessary., all traffic control signage will meet Pfizer requirements before being installed. Fire dept. access will be maintained and kept open for emergency responders.

End Site Specific. See “Consigli Safety Program” for more information.

[PA1]MEWPs need to be inspected prior to each use (this is a Pfizer requirement)

[PA2]MEWPs cannot be moved while in an elevated position. If the MEWP needs to relocate, the basket needs to be lowered first. Operators must exit the platform when moving through areas with limited height or width.

[PA3]Follow the Pfizer Cambridge electrical safety program and NFPA 70E standard to establish an electrically safe work condition.

[PA4]610 Main St

Back– End of Environmental Emergency Contact and Management Response